Here is some General info that Daltile Gives for maintaining Tile and Grout.
This is important to protect your investment, We recommend Following these steps, because regouting is a tedious and costly option.
Please Contact us at Kiezebrinktileandstone@yahoo.com or
visit our website www.kiezebrinktileandstone.com for any questions.
Ceramic Tile
Contaminants and spills on a glazed ceramic tile
are, generally, easier to clean than most other unglazed ceramic and
porcelain surfaces. Glazed tile products should be cleaned routinely with an all-purpose, low VOC household or commercial cleaner.
The product chosen should also be grout joint cleaning compatible. The
type of product may vary depending on the tile application and use. A
multipurpose spray cleaner, which removes soap scum, hard water
deposits, and mildew designed for every day use, can be used on wall
tile areas in residential baths and showers.
The entire area should be cleaned and scrubbed with cleaner solution
through the use of a cotton mop, cloth, sponge, or non-metallic brush.
The entire area should be rinsed with clean water to remove any cleaning
solution residue. Remember that you should sweep or vacuum floor areas
prior to cleaning to remove any dust or debris. Routine cleaners should
never contain hazardous or polluting products including, but not limited
to acids or ammonia. Acids can damage the grout and the glazed surface
of the tile, and ammonia can discolor the grout.Unglazed tile should be cleaned routinely with concentrated tile cleaners that have a neutral pH for safe regular use. These cleaners are better suited at removing grease, oils and normal spills from unglazed products. Again these products will vary depending on the application, amount of traffic and the use. The product chosen should also be compatible with cleaning the grout joints at the same time.
Removal of Sealers/Waxes/Floor Finishes:
If you need to remove a topical sealer or floor wax from a ceramic
tile you should use a Tile Sealer & Adhesive remover. Always test a
small area first. Apply a liberal amount of undiluted sealer &
adhesive remover to a manageable area. Allow setting without drying
until coating or residue softens. Reapply if necessary until sealer
softens and can be removed. If necessary, agitate with white nylon scrub
pad. Wipe up the residue with a cotton towel or sponge. Rinse
thoroughly with clean water. Do not use on natural stone products.
Glass Tiles:
For routine cleaning, use any non-abrasive cleaning compound recommended for either glass or tile
Metal Signatures/Metal Ages/Urban Metals:
To clean, use a liquid non-abrasive household cleaner.
DO NOT use scouring pads, steel wool, sandpaper or other abrasive products.
Avoid cleaners containing ammonia, bleach, abrasives, or other hazardous/polluting compounds.
Always test in small inconspicuous area while using a new cleaner to ensure compatibility.
Ceramic Tile - Grout Care
Grout is the material used to fill the spaces between the individual
tiles. Grout comes in many colors. While color is important to the final
finished look of the tile installation, it has little effect on the
functionality of the grout. The purpose of grout is, simply, to fill the
joint between the tiles and becomes a permanent, integral component of
the finished installation.
Penetrating/Impregnating Sealer:
Most tile installations use cementitious grouts. This type of grout
should be sealed after installation to prevent the color from staining.
The grout should be sealed with a penetrating/impregnating sealer (often
called grout sealers) which does not contain silicone, as silicone can
shorten the useful life of the sealer. Epoxy grouts, conversely, are
chemically cured and acid resistant and, as a result, do not require a
sealer. The application of a good quality penetrating/impregnating
sealer into the grout joints of a cementitious grout will not change the
natural color of the grout, but will prevent the penetration of
moisture, simplify maintenance, and help prevent staining or
discoloration. Only the grout needs to be sealed, not glazed floor or
wall tiles. Grout can be sealed seventy-two hours after installation.There are different grades of penetrating/impregnating sealers, therefore the useful life and price will differ between a low quality and high quality sealer. You may need to reapply the sealer on an annual basis depending on the sealer quality, traffic patterns, and maintenance routine. Some sealers have multiple year warranties for useful life. Refer to the manufacturer warranty, technical & product information for specific details on product installation, useful life, and product applications (including any warnings) before use.
Grout Maintenance:
Neither sealing the grout nor using a 100% Epoxy Grout will guarantee
against surface build-up or discoloration of the grout. Grout needs to
be cleaned on a periodic basis to remove any surface build-up. Routine
grout cleaning can be done with a daily concentrated household or
commercial cleaner depending on the application. When heavy duty grout
cleaning is required, you will need to use a professional strength Tile
& Grout Cleaner that is capable of removing grease, soap scum, body
oil, mildew stains, algae, and synthetic or acrylic waxes from the grout
joints. However, such a product should contain non-polluting chemicals
and low VOC levels. This type of product can be purchased from most Home
Centers, or through your local professional Floor Covering Dealer.
Grout Color Restoration:
When grout has been stained to the point that it cannot be maintained
or returned to its natural color, you can return the grout back to its
original color or any other color through the use of a "grout stain".
Grout Stains are epoxy-based products that are specifically designed to
penetrate into the grout and seal the surface with a permanent color.
Once the grout has been stained there is no need to seal it any further
with a penetrating/impregnating sealer. Prior to staining, the grout
joint should be cleaned thoroughly to remove any dirt, oils, grease or
sealers with a professional strength Tile & Grout Cleaner. This can
be purchased from most Home Centers or through your local Professional
Floor Covering Dealer.
Ceramic Tile - New Installations
Immediately after tile has been properly installed and grouted, the
new installation should be covered with brown paper to protect it from
debris during the remaining construction process. The grout joints
should be dampened daily with clear water using a clean sponge or mop
during the first 7 days. This procedure facilitates the grout cure and
color lock. The paper will allow for two important things: (1) to
protect the newly installed tile grout and (2) to allow moisture to
escape from the grout as it cures further protecting the look and
utility of the floor. This is an important step in achieving color
consistency. Never use plastic or non-absorbent materials to protect
freshly installed tile. These types of non-absorbent products will trap
moisture causing the grout to discolor during the curing period. The
protective brown paper should remain until construction is complete and
the floor is opened for intended (post-construction) use.Grout haze is a film that has been left behind on the surface of the tile as part of the final grouting process. Usually this is buffed off the surface after the grout has achieved its initial 12 to 24 hour cure. The removal of the haze is often difficult when buffing with a clean rag or floor machine. Cementitious grout haze can be successfully removed with "Sulfamic" acid, which is a mild acid that attacks and breaks down cement smears. There are several products on the market called grout haze removers, which usually contain Sulfamic acid. Sulfamic acid can also be purchased in powder form and mixed with water to different strengths by qualified professionals. Similarly, 100% Solids Epoxy Grout haze can be removed with an Epoxy Haze Remover. These removers are formulated to safely and quickly remove cured epoxy haze from new tile installations. Their unique formulation will soften most epoxy hazes for easy removal without damaging the grout or tile, usually in one application. Sulfamic acid or grout removers should never be used on Natural Stone products.
Natural Stone - Routine Care
Natural Stone Care & Maintenance
To insure your natural stone products will provide you with a
lifetime of aesthetics and utility, a proper maintenance program is
crucial. Natural Stone products are porous by nature and require a
different maintenance program than traditional ceramic tile.Natural stone requires a different maintenance routine than traditional, man-made ceramic tile. Many of the cleaners acceptable for use on ceramic tile can stain, damage or dull stone. Dirt and dust will scratch the surface of stone. Therefore, stone floors should be vacuumed or dust mopped frequently to remove abrasive agents from the stone surface. Natural stone should be cleaned with neutral cleaners. Stone cleaners should never contain acid or bleach. Acids, even a light solution of vinegar and water, will etch and eventually damage natural stone.
Stone Cleaners:
Only use cleaners specifically designed for cleaning stone. These
cleaners contain no acids and are concentrated neutral pH cleaners that
will not affect existing sealers or wax-type coatings. The surface of
the stone should be dampened with clear water. This will keep the
cleaning solution on the surface so it can be effective. A solution of
the cleaner and water missed to manufacturer instructions should be
applied to the stone surface with a sponge or mop. On walls, kitchen
counters or vanity tops, a spray bottle can be used to apply the
cleaning solution. Allow sitting for manufacturers specified amount of
time (usually 3 to 5 minutes). Agitate with a sponge, synthetic mop,
soft bristle brush or through the use of a floor-scrubbing machine. Mop
up dirty solution and buff dry.Once the stone has been cleaned, you can periodically apply a Spray-Buff wax-type floor finish to enhance the beauty and luster of polished stone (including countertops). Apply the finish with a spray applicator and buff immediately with a white nylon pad. Reapply as often as needed, depending on volume of surface traffic and consistency of routine maintenance program. This product is not designed to restore the original shine, but is intended to maintain and protect the original shine. This can be purchased from most Home Centers or through your local Professional Floor Covering Dealer.
Heavy-Duty Stone Cleaning:
When some areas have been neglected, you will need to use a
heavy-duty non-hazardous and non-polluting stone cleaner and degreaser
to effectively remove dirt, grease, grime, waxes and floor finishes. An
optimal heavy-duty cleaner should contain low percentages of volatile
organic compounds. These cleaning products are concentrated and designed
to deep clean the stone without damaging it. Apply the solution of the
cleaner and water mixed to manufacturer instructions to the stone
surface with a sponge or mop. Allow setting for manufacturer-specified
amount of time. Agitate with a sponge, synthetic mop, and soft bristle
brush or through the use of a floor-scrubbing machine. Mop up dirty
solution and buff dry. Be sure to change out the cleaning solution every
100 square feet to avoid reintroducing dirty water during the cleaning
process. Rinse thoroughly with clean water when finished. After cleaning
you may apply the Spray-Buff wax-type floor finish to enhance the
natural shine.
Stain Removal:
Stone poultice will remove stains and grout haze from stone. Poultice
is a fine, nonacidic, absorptive clay cleaning powder that removes
deep-set oil stains, grease and light cementitious grout haze from
polished and unpolished natural stone.CAUTION: Poultice may dull the shine of the polished stone. If this occurs you will need to use a marble polish to restore the natural shine.
Restoration:
If a marble finish has become dull, scratched or etched, you can
restore the natural shine through the use of a marble polish. Some
marble polishes are available in kits. The process can be enhanced with
the use of floor buffing machines. The process is generally a
re-crystallization process to remove fine scratches and restore the
original shine and polish to the stone. This is not an application of a
topical sealer or wax to cover-up damaged or worn surfaces.
Natural Stone - New Installations
Sealing is strongly recommended for newly installed marble and other
natural stone to provide maximum below surface stain protection. Consult
your Professional Floor Covering Dealer or Home Center Store to ensure
that you select a high quality sealer to protect your natural stone.
Immediately after natural stone has been installed and grouted, the new
installation should be covered with brown paper to protect it from
debris during the remaining construction process. The protective brown
paper should remain in place until construction is completed and the
area is opened to intended (post-construction) use.
Pre-grout Sealing:
A non-sanded grout is strongly recommended for natural stone
installations due to the narrow grout joints customarily preferred. This
type of grout has very fine particles of cement, polymers and color
pigments that can penetrate the microscopic pores of the stone surface
where they become trapped and appear as a stain in the stone. Therefore,
all travertine, slate, tumbled stone and honed/flamed/unpolished
granite should be sealed prior to the grouting process to protect them
from staining. The application of a good quality sealer should be used
as a grout sealer and applied again as the final sealing process once
the installation is finished.
Sealing:
A premium natural look penetrating/impregnating sealer is the normal
choice on polished or honed marble, limestone, granite, or where the
natural color of a slate is desired. A stone enhancer sealer is often
used on tumbled, antique stones or on slate where a darker, enriched or
highlighted character is desired. When choosing either one of these
types of sealers, make sure the brand you have chosen is formulated to
provide maximum stain protection for stone products. Stone products
should be tested periodically per manufacturer's instructions to insure
that the sealer is working effectively.Penetrating/impregnating stone sealers are a no-sheen, natural look sealer that can be water-based or solvent-based, good for interior and exterior applications. Most quality sealers of this type are rated to protect the stone for several years.
Stone enhancer sealers are also a no-sheen, penetrating/impregnating sealer that is formulated to darken, enrich and highlight the natural color and beauty of stone products. They will rejuvenate and improve the appearance of worn and weathered stone. Always test loose pieces of stone to ensure desired effect with enhancing sealers. However, they will also darken the color of grout joints. They are, generally, suitable for interior and exterior use, and rated to protect the stone for several years.
Always reference manufacturer's literature for specific information on the duration of the sealer's protection and make sure that the sealer is applied in strict accordance with the manufacturer's instructions.
Finishing:
A stone floor finish should be applied to a polished natural stone
floor only. This type of product will help enhance the shine and provide
a protective coating for "soft" or polished marbles. Verify the finish
is a wax-type finish designed to add luster and enhance the beauty of
sealed and polished natural stone only. A topical finish may change the
appearance and performance of your stone, so always test a small area
first. Application of topical sealer or wax
should never be done as an attempt to add a shine to a honed, scratched
or non-polished stone product. This will only create maintenance and/or
slip resistance problem.
Saltillo Tile - Routine Care
Soft clay tiles are categorized as specialty use products, and as
such they are generally not governed by the same requirements as glazed
or unglazed ceramic tile. These products will require some type of
topical sealer protection. These sealers are designed to provide stain
resistance and a durable finish to protect clay tile against wear.
Pre-sealing the tile prior to grouting will act as a pre-grout sealer,
provided it is applied over a clean tile surface. An additional final
coat over the grouted floor will complete the sealing process along with
providing the final grout stain protection.There are two common types of sealers used today for sealing specialty tiles. The first is a water-based blend of acrylic polymers. This product allows for moisture vapor transmission, and it can be reapplied over itself, without stripping or removing the old sealer when the original application has become worn. The second type is a solvent-based sealer. Solvent-based sealers are not as forgiving after they have become worn, they must be stripped and removed prior to reapplication. Both types should be UV stable, which means the ultra violet rays from the sun should not break them down. You should always follow the manufacturer's instructions for use, maintenance and precautions.
The expected wear of the topical sealer will vary depending on the hardness, surface texture, type or area, usage, and type of maintenance products used. However, the average expected use life of the sealer, when properly prepared, is a maximum of 3 years. Harsh cleaning methods, high-alkaline or solvent-based cleaners can significantly lower the expected life of the sealer. Concentrated tile cleaners are recommended for routine cleaning.
Maintenance Cleaning
Highly alkaline, acidic, ammoniated, abrasive cleaners and/or bleach
may break down the sealer, adversely affecting repellency and may not be
good for the tile or grout. Use neutral cleaners specially formulated
for tile and grout that are low VOC, non-hazardous and non-polluting.
For routine cleaning:
We recommend DuPont™ StoneTech® Professional Stone & Tile Cleaner.
Mix 2 ounces of Stone & Tile Cleaner
concentrate in 1 gallon of warm or hot water. (Note: One gallon of
concentrate makes 64 gallons of cleaning solution.
Apply mixed solution with a damp mop, sponge or appropriate professional cleaning equipment.
Clean entire area with mop, changing mop water often to ensure that soil is not re-deposited. Wipe or rinse cleaned area.
Let area dry completely before using.
You may also use DuPont™ StoneTech® Professional Stone & Tile Cleaner in the ready-to-use spray bottle or wipes.
Re-Sealing and Protecting:
For interior surfaces, resealing should be performed every 3-5 years.
For exterior surfaces, resealing should be performed every 1-3 years.
We recommend the use of a heavy-duty sealant that is low in VOC content
and does not contain any hazardous materials.
Quarry Tile
Recommended Sealers Pre-Grout sold through Dal Tile stores may include
- DuPont Stone Tech Professional Heavy Duty Sealer (follow manufacturer instructions for application process)
- Aqua Mix Ultra-Solv (follow manufacturer instructions for application process)
- DuPont Stone Tech Professional Heavy Duty Coating Stripper or KlenzAll (follow manufacturer instructions for application process)
- Aqua Mix “1 & 2 Deep Clean” (follow manufacturer instructions for application process)
- Quarry tile is an issue with mop heads as many quarry tiles are very abrasive. Old fashion string mops (cotton or rag material) will shred easily on a course or abrasive finish. Even the nylon ones don’t fare well. The alternative is stitched end (tailband) microfiber or looped end knits (rough surface heads), tube mop heads.
- A wet microfiber mop rated for heavy duty use
We recommend the use of a sealer prior to grouting.
One Quartz Surfaces - Routine Care
One Quartz Surfaces are virtually maintenance free and can be cleaned with extreme ease.
Common household spills – such as, tea,
coffee, lemon juice, soda, fruit, vegetable juice, olive oil or grease
spills – are easily removed and the surface restored to its original
appearance.
Some One Quartz Surface colors and
finishes liked honed, matt, etc., are more sensitive to grease or
finger-prints and may require extra care during routine cleaning.
Quartz is one of the hardest materials in
nature, which is your assurance that your One Quartz Surfaces will not
easily scratch or chip. The use of a cutting board is nevertheless
recommended.
To maintain the natural beauty of One
Quartz Surfaces, do not place hot skillets or roasting pans directly
onto the surface but use a trivet instead.
For routine cleaning, use a damp cloth or
paper towel and, if necessary, a small amount of mild soap. Once clean,
rinse and dry surface thoroughly.
For stubborn or dried spills, use a
nonabrasive cleaning pad such as a white 3M Scotch-Brite® scrub pad
combined with a small amount of mild soap or specialized stone cleaner.
One Quartz Surfaces floors in high traffic areas should be cleaned daily
with a clean, dry dust mop or soft bristle broom.
One Quartz Surfaces floors in low traffic
areas can be cleaned less frequently using the same method. Spills
should be spot treated with the use of a damp mop or cloth towel and, if
necessary, a small amount of mild soap or specialized stone cleaner.
A floor machine such as a slow speed
buffer or walk behind scrubber can be used for larger commercial
environments. Be sure to rinse thoroughly to remove any haze residue
that may diminish the shine and beauty of the floor.
For Heavily soiled floors, as with any floor, it makes sense to clean up spills as soon as possible.
Avoid exposing One Quartz Surfaces to
chemicals and solvents, especially paint removers or furniture strippers
containing trichlorethane or methylene chloride. Keep nail polish
remover, bleach or cleansers that contain bleach, bluing, permanent
markers or inks. While casual exposure to alkaline materials will not
damage One Quartz Surfaces, highly alkaline (high-pH) cleansers are not
recommended when cleaning One Quartz Surfaces. If any of the substances
listed above come into contact with One Quartz Surfaces, rinse the
exposed surface immediately and thoroughly with plenty of clean water.
Do not use strong abrasive and/or
alkaline cleaning products. Always follow the manufacturers’ dilution
instructions and recommendations.
No comments:
Post a Comment